序号  标准号 标准名称
1 AGMA 94FTM10-1994Computerized Design and Generation of Low-Noise Gears with Localized Bearing Contact
2 AGMA 94FTM11-1994Development of Transfer Gear Noise of 4X4 Transmission for Recreational Vehicles
3 AGMA 94FTM2-1994An Analytical Method for the Calculation of the Efficiency of Planetary Gears
4 AGMA 94FTM3-1994Application of Ausforming to Gear Finishing - Process Design and Manufacturability Issues
5 AGMA 94FTM4-1994Load Carrying Capacity of Nitrided Gears
6 AGMA 94FTM5-1994A Special CVT for a New Power Train Concept
7 AGMA 94FTM6-1997A Boundary Element Procedure for Predicting Helical Gear Root Stresses and Load Distribution Factors
8 AGMA 94FTM7-1994Allowable Surface Compressive Stresses of Gear Teeth Made of Cast Iron Tempered Carbon Steels and Tempered Alloys Steels
9 AGMA 94FTM8-1994Reference Point Mesh Stiffness and Dynamic Behavior of Solid Semi-Solid and Thin Rimmed Spur Gears
10 AGMA 94FTM9-1994Analytical and Experimental Vibration Analysis of a Damaged Gear
11 AGMA 94FTMS1-1994Computer-Aided Numerical Determination of Hofer Lewis Niemann and Colbourne Points
12 AGMA 95FTM1-1995Detection of "Hidden Runout"
13 AGMA 95FTM10-1995Efficiency of High Contact Ratio Planetary Gear Trains
14 AGMA 95FTM11-1995Feature-Based Definition of Bevel Gears
15 AGMA 95FTM12-1995Flank Modifications in Bevel Gears Using a Universal Motion Concept
16 AGMA 95FTM3-1995The Effect of Manufacturing Errors on the Predicted Dynamic Factors of Spur Gears
17 AGMA 95FTM4-1995An Experimental Test Stand to Measure Loaded Transmission Error in Fine-Pitch Plastic Gears
18 AGMA 95FTM5-1995The Surface Fatigue Life of Contour Induction Hardened AISI 1552 Gears
19 AGMA 96FTM2-1996The New Way of Manufacturing Bevel and Hypoid Gears in a Continuous Process
20 AGMA 96FTM12-1996An Investigation of Globoidal Wormgear Drives
21 AGMA 96FTM3-1996Noise Reduction Through Generated Engagement Relief Modification
22 AGMA 97FTM11-1997Non - Dimensional Characterization of Gear Geometry Mesh Loss and Windage
23 AGMA 97FTM10-1997UltraSafe Gear Systems for Critical Applications - Initial Development
24 AGMA 97FTM1-1997Calibration of Gear Measuring Instruments and Their Application to the Inspection of Product Gears
25 AGMA 96FTM9-1996The Development of a Practical Thermal Rating Method for Enclosed Gear Drives
26 AGMA 96FTM8-1996Thermal Rating of Gear Drives Balance Between Power Loss and Heat Dissipation
27 AGMA 96FTM7-1996Dynamic Distribution of Load and Stress on External Involute Gearings
28 AGMA 96FTM6-1996Thermal Rating of Gear Drives Balance Between Power Loss and Heat Dissipation
29 AGMA 96FTM5-1996Differential Crowning: A New Weapon Against Gear Noise and Dynamic Load
30 AGMA 96FTM4-1996Traceable Calibration of Master Gears at PTB
31 AGMA 97FTM12-1997Introduction of a Jobbing System for Bevel and Hypoid Gears
32 AGMA 97FTM2-1997Determining Sound Power Levels of Enclosed Gear Drives Using the Sound Intensity Method
33 AGMA 97FTM3-1997Detection of Fatigue Cracks in Gears with the Continuous Wavelet Transform
34 AGMA 97FTM4-1997Measurement and Predictions of Plastic Gear Transmission Errors with Comparisions to the Measured Noise of Plastic and Steel Gears
35 AGMA 97FTM5-1997Improved Finite Element Model for Calculating Stresses in Bevel and Hypoid Gear Teeth
36 AGMA 97FTM6-1997Bending Load on Internal Gears of Planetary Gear Sets
37 AGMA 97FTM7-1997Bending Load on Internal Gears of Planetary Gear Sets
38 AGMA 97FTM8-1997 发New Guidelines for Wind Turbine Gearboxes
39 AGMA 97FTM9-1997Relations Between Wear and Pitting Phenomena in Worm Gears
40 AGMA 97FTMS1-1997Coordinate Measurement and Reverse Engineering of ZK Type Worm Gearing
41 AGMA 115.01-1959Reference Information Basic Gear Geometry R(1989)
42 AGMA 203.03-73-1973Fine-Pitch On-Center Face Gears for 20-Degree Involute Spur Pinions
43 AGMA 217.01-1965Information Sheet Gear Scoring Design Guide for Aerospace Spur and Helical Power Gears
44 AGMA 299.01-I-1978Sound Manual Section I: Fundamentals of Sound as Related to Gears R(1994)
45 AGMA 299.01-II-1980Sound Manual Section II: Sources Specifications and Levels of Gear Sound R(1994)
46 AGMA 299.01-III-1980Sound Manual Section III: Gear-Noise Control R(1994)
47 AGMA 422.03-1984Standard Practice for Helical and Herringbone Speed Reducers for Oilfield Pumping Units R(1992)
48 AGMA 427.01-1976Information Sheet Systems Considerations for Critical Service Gear Drives
49 AGMA 431.01-1964Design Procedure for Aircraft Engine and Power Take-Off Bevel Gears R(1974)
50 AGMA 510.03-1984Nomenclature for Flexible Couplings
51 AGMA 900-F96-1996Style Manual for the Preparation of Standards Information Sheets and Editorial Manuals
52 AGMA 901-A92-1992A Rational Procedure for the Preliminary Design of Minimum Volume Gears
53 AGMA 904-C96-1996Metric Usage
54 AGMA 906-A94-1994Gear Tooth Surface Texture with Functional Considerations Replaces 11801
55 AGMA 908-B89-1989Geometry Factors for Determining the Pitting Resistance and Bending Strength of Spur Helical and Herringbone Gear Teeth Revision of 22601 R(1995)
56 AGMA 910-C90-1990Formats for Fine-Pitch Gear Specification Data Revision of 11402 R(1995)
57 AGMA 911-A94-1994Design Guidelines for Aerospace Gearing Replaces 41102
58 AGMA 913A-1998Method for Specifying the Geometry of Spur and Helical Gears
59 AGMA 915-3A-1999Inspection Practices - Gear Blanks Shaft Center Distance and Parallelism ISO/TR 10064-3: 1996 (MOD)
60 AGMA 917-B97-1997Design Manual for Parallel Shaft Fine-Pitch Gearing
61 AGMA 918-A93-1993A Summary of Numerical Examples Demonstrating the Procedures for Calculating Geometry Factors for Spur and Helical Gears
62 AGMA 921-A97-1997Recommended Practices for Design and Specification of Gearboxes for Wind Turbine Generator Systems
63 AGMA 922-A96-1996Load Classification and Service Factors for Flexible Couplings Revision of 51402
64 AGMA 9008-B00-2000Flexible Couplings - Gear Type - Flange Dimensions Inch Series Revision of AGMA 51601
65 AGMA 9005-D94-199Industrial Gear Lubrication REPLACES 2500425102
66 AGMA 9004A-1999Flexible Couplings - Mass Elastic Properties and Other Characteristics
67 AGMA 9003-A91-1991Flexible Couplings - Keyless Fits
68 AGMA 9002-A86-1986Bores and Keyways for Flexible Couplings (Inch Series) Redesignation of AGMA 518xx; Supersedes 51102 51203 51301 R(1994)
69 AGMA 6030-C87-1987 发Design of Industrial Double-Enveloping Wormgears Revision of 34202 R(1994)
70 AGMA 6032-A94-1994Standard for Marine Gear Units: Rating
71 AGMA 6033-A88-1988Standard for Marine Propulsion Gear Units Part 1 Materials
72 AGMA 6034-B92-1992Practice for Enclosed Cylindrical Wormgear Speed Reducers and Gearmotors
73 AGMA 6109-A00-2000Standard for Gearmotor Shaft Mounted and Screw Conveyor Drives Metric Edition; Revision of ANSI/AGMA 6019-E89 and 6021-G89
74 AGMA 6110-F97-1997Standard for Spur Helical Herringbone and Bevel Enclosed Drives Metric Edition of ANSI/AGMA 6010-F97
75 AGMA 6123-A88-1988Design Manual for Enclosed Epicyclic Metric Module Gear Drives See ANSI/AGMA 6023-A88 for Non-Metric Version R(1993)
76 AGMA 6133-B98-1998Materials for Marine Propulsion Gearing Revision of ANSI/AGMA 6033-A88; Metric Edition of ANSI/AGMA 6033-B98
77 AGMA 9000-C90-1990Flexible Couplings - Potential Unbalance Classification Revision of 51502 R(1996)
78 AGMA 9001-B97-1997Flexible Couplings-Lubrication
79 AGMA 6005-B89-1989Power Rating for Helical and Herringbone Gearing for Rolling Mill Service Revision of 32301
80 AGMA 6008-A98-1998Specifications for Powder Metallurgy Gears
81 AGMA 6009-A00-2000Standard for Gearmotor Shaft Mounted and Screw Conveyor Drives Revision of ANSI/AGMA 6019-E89 and 6021-G89
82 AGMA 6010-F97-1997Standard for Spur Helical Herringbone and Bevel Enclosed Drives
83 AGMA 6011-H98-1998Specification for High Speed Helical Gear Units
84 AGMA 6017-E86-1986Rating and Application of Single and Multiple Reduction Double- Enveloping-Worm and Helical-Worm Speed Reducers Revision and Redesignation of 44104 R(1994)
85 AGMA 6021-G89-1989Shaft Mounted and Screw Conveyor Drives Using Spur Helical and Herringbone Gears Revision of 48006; Revised by ANSI/AGMA 6109-A00 and ANSI/AGMA 6009-A00 R(1994
86 AGMA 6022-C93-1993Design Manual for Cylindrical Wormgearing Revision of 34102
87 AGMA 6023-A88-1988Design Manual for Enclosed Epicyclic Gear Drives Errata July 1991 R(1993)
88 AGMA 6025-D98-1998Sound for Enclosed Helical Herringbone and Spiral Bevel Gear Drives Revision of 6025-C90
89 AGMA 2010-A94-1994Measuring Instrument Calibration - Part I Involute Measurement
90 AGMA 2011-A98-1998Cylindrical Wormgearing Tolerance and Inspection Methods Replacement of AGMA 39003a
91 AGMA 6004-F88-1988Gear Power Rating for Cylindrical Grinding Mills Kilns Coolers and Dryers Revision of 32105
92 . AGMA 6002-B93-1993Design Guide for Vehicle Spur and Helical Gears Revision of 17001
93 AGMA 6001-D97-1997Specification for Measurement of Linear Vibration on Gear Units
94 AGMA 6000-B96-1996Specification for Measurement of Linear Vibration on Gear Units
95 AGMA 2114-A98-1998Measuring Instrument Calibration Gear Pitch and Runout Measurements
96 AGMA 2113-A97-1997Measuring Instrument Calibration Gear Tooth Alignment Measurement
97 AGMA 2110-A94-1994Measuring Instrument Calibration - Part I Involute Measurement (Metric)
98 AGMA 2101-C95-1995Fundamental Rating Factors and Calculation Methods for Involute Spur and Helical Gear Teeth Metric Edition of 2001-C95; Errata 1996
99 AGMA ISO 1328-2-1999Cylindrical Gears - ISO System of Accuracy - Part 2: Definitions and Allowable Values of Deviations Relevant to Radial Composite Deviations and Runout Information ISO 1328-2: 1997 IDT
100 AGMA 2000-A88-1988Gear Classification and Inspection Handbook Tolerances and Measuring Methods for Unassembled Spur and Helical Gears (Including Metric Equivalents) Errata - 07/90; Errata - 01/89; Partial Revision of AGMA 39003
1 2